200-105 Exam Questions Answers

Valid4sure 200-105 VCE Practice Test

New Updated 200-105 Exam Questions from valid4sure 200-105 PDF dumps! Welcome to download the newest valid4sure 200-105 VCE dumps: (267 Q&As)

• Cisco Networking Devices Part 2 (ICND2 v3.0)

Keywords: 200-105 exam dumps, 200-105 exam questions, 200-105 VCE dumps, 200-105 PDF dumps, 200-105 practice tests, 200-105 study guide, 200-105 braindumps,

PS. New 200-105 dumps PDF – https://www.valid4sure.com/200-105-exam-answers.html

200-105 Practice Test Questions Answers – 200-105 braindump

QUESTION NO: 1

Which statement about QoS default behavior is true?

A.         Ports are untrusted by default.

B.         VoIP traffic is passed without being tagged.

C.         Video traffic is passed with a well-known DSCP value of 46.

D.         Packets are classified internally with an environment.

E.         Packets that arrive with a tag are untagged at the edge of an administrative domain.

Answer: E

Frames received from users in the administratively-defined VLANs are classified or tagged for transmission to other devices. Based on rules that you define, a unique identifier (the tag) is inserted in each frame header before it is forwarded. The tag is examined and understood by each device before any broadcasts or transmissions to other switches, routers, or end stations. When the frame reaches the last switch or router, the tag is removed before the frame is sent to the target end station. VLANs that are assigned on trunk or access ports without identification or a tag are called native or untagged frames.

For IEEE 802.1Q frames with tag information, the priority value from the header frame is used. For native frames, the default priority of the input port is used.

Each port on the switch has a single receive queue buffer (the ingress port) for incoming traffic. When an untagged frame arrives, it is assigned the value of the port as its port default priority. You assign this value by using the CLI or CMS. A tagged frame continues to use its assigned CoS value when it passes through the ingress port.

QUESTION NO: 2

Router edge-1 is unable to establish OSPF neighbor adjacency with router ISP-1. Which two configuration changes can you make on edge-1 to allow the two routers to establish adjacency? (Choose two.)

A.         Set the subnet mask on edge-1 to 255 255.255.252.

B.         Reduce the MTU on edge-1 to 1514.

C.         Set the OSPF cost on edge-1 to 1522.

D.         Reduce the MTU on edge-1 to 1500.

E.         Configure the ip ospf mtu-ignore command on the edge-1 Gi0/0 interface.

Answer: D, E

A situation can occur where the interface MTU is at a high value, for example 9000, while the real value of the size of packets that can be forwarded over this interface is 1500.

If there is a mismatch on MTU on both sides of the link where OSPF runs, then the OSPF adjacency will not form because the MTU value is carried in the Database Description (DBD) packets and checked on the other side.

QUESTION NO: 3

Which statement about MPLS is true?

A.         It operates in Layer 1.

B.         It operates between Layer 2 and Layer 3.

C.         It operates in Layer 3.

D.         it operates in Layer 2.

Answer: B

MPLS belongs to the family of packet-switched networks. MPLS operates at a layer that is generally considered to lie between traditional definitions of OSI Layer 2 (data link layer) and Layer 3 (network layer), and thus is often referred to as a layer 2.5 protocol.

QUESTION NO: 4

Which statement about named ACLs is true?

A.         They support standard and extended ACLs.

B.         They are used to filter usernames and passwords for Telnet and SSH.

C.         They are used to filter Layer 7 traffic.

D.         They support standard ACLs only.

E.         They are used to rate limit traffic destined to targeted networks.

Answer: A

Named Access Control Lists (ACLs) allows standard and extended ACLs to be given names instead of numbers. Unlike in numbered Access Control Lists (ACLs), we can edit Named Access Control Lists. Another benefit of using named access configuration mode is that you can add new statements to the access list, and insert them wherever you like. With the legacy syntax, you must delete the entire access list before reapplying it using the updated rules.

QUESTION NO: 5

Which two switch states are valid for 802.1w? (Choose two.)

A.         listening

B.         backup

C.         disabled

D.         learning

E.         discarding

Answer: D, E